hardie trim installation hz10robotic rideable goat

A). Maintain clearance between trim and adjacent finished grade. Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns. Touch-up nicks, scrapes, and nail heads in pre-finished siding using the manufacturer's touch-up kit pen. Vented Soffit Panels: HardieSoffit HZ10 Vented Panels. Installer Qualifications: Minimum of 2 years' experience with installation of similar products. 101-107, Products Installation Guide_HardieShingle pg. Type: Smooth vented, 24 inches (610 mm) by 8 feet (2438 mm). in the first 10 ft. Do not use Hardie Architectural Panels in Fascia or Trim applications. 90 percent drainage efficiency shall be used. Product: 4/4 NT3 Boards, 11-1/4 inch (286 mm) width. Breathing excessive amounts of respirable silica dust can also cause a disabling and potentially fatal lung disease called silicosis, and has been linked with other diseases. Type: Textured Cedarmill vented, 24 inches (610 mm) by 8 feet (2438 mm). The Flat Tabs should be attached to the trim in an alternating pattern to the top and bottom of the band board (Figure 30 and 31). Type: Hardie Architectural Knockdown Panel4 by 12 feet (1219 by 3658 mm). Never use continuous-edge diamond blades, abrasive discs, or high tooth count circular saw blades 9 Caution: Tools and blades designed to reduce breathable silica do not always result in safe levels by themselves. Squareness: Less than1/32 inches per ft (2.6 mm per m) of length. Wood Framing: 0.121 inch (3 mm) shank by 0.371 inch (9.4 mm) head by 1-1/4 inches (32 mm) corrosion resistant roofing nails. Substrate: Install a minimum 7/16 inch (11 mm) thick OSB wall sheathing or equivalent braced walls complying with applicable building codes. Figura 26 La proteccin ha de remeterse por debajo de la barrera resistente al agua y sobre las lengetas planas. 4/4,5/4 boards are decorative non-load bearing trim products. 2X Smooth HardieTrim manufactured by James Hardie Building Products, Inc. HardieTrim HZ10 Crown moulding manufactured by James Hardie Building Products, Inc. Wood Framing: 4d common corrosion resistant nails. CAL-FIRE, Fire Engineering Division Building Materials Listing - Wildland Urban Interface (WUI) Listed Product. James Hardie siding and trim products must be kept dry at all times prior to installation. Type: HardieShingle Half Round Notched Panel 48 inches (1219 mm) wide by 19 inches (483mm) high with 7 inches (178 mm) exposure. Hardie Architectural Panels as manufactured by James Hardie Building Products, Inc. A non-combustible fiber-cement panel. May be used in ASTM E119 fire resistance rated assemblies as listed by Warnock Hersey. CUT EDGE TREATMENT Caulk, paint or prime all field cut edges. Type: Select Cedarmill 8-1/4 inches (210 mm) with 7 inches (178 mm) exposure. NER-405. NIOSH-approved respirators can be used in conjunction with above cutting practices to further reduce dust exposures. screws hardie james Type: Beaded 8-1/4 inches (210 mm) with 7 inches (178 mm) exposure. Section 1405.16 as ASTM C 1186 Grade II, Type A Fiber Cement. The current user is not setup as a shopper and cannot add to cart. Fastener Positioning: Position fasteners 3/8 inches (9.5 mm) from panel edges and no closer than 2 inches (51 mm) away from corners when using soffit greater than 12 inch (305 mm) wide and no closer than 1 inch (25 mm) away from corners when using soffit that is less than or equal to 12 inch (305 mm) wide. ! Masonry Walls: Aerico Stud Nail, ET&F ASM No.-144-125, 0.14 inch (3.6 mm) shank by 0.30 inch (7.6 mm) head by 2 inches (51 mm) long corrosion resistant nails. Type: HardieShingle Individual Shingles 12 inches (305 mm) wide by 18 inches (457 mm) high with 8 inches (203 mm) exposure. Please contact James Hardie or consult with a qualified industrial hygienist if unable to adhere to the recommended cutting instructions. For further information, refer, to our installation instructions and Material Safety Data Sheet available at www.jameshardie.com or by calling 1-800-9HARDIE (1-800-942-7343). Install water-resistive barriers and claddings to dry surfaces. Minimum fastener guide for finish nailing: Store flat and keep dry and covered prior to, may result in shrinkage at butt joints. Type: Stucco Vertical siding panel 4 feet by 9 feet (1219 mm by 2743 mm). For horizontal panel orientations only. Fasteners must be no closer than 1" from ends of trim and spaced a maximum of 16" o.c. Inside Corner Trim: Aluminum extrusion to be used for inside corners. Jointing Methods: Install panels in moderate contact at ends, provide PVC or metal jointers, battens or leave appropriate gap and caulk. Type: Sierra 8 inches (203 mm) Vertical siding panel 4 feet by 9 feet (1219 mm by 2743 mm). Seal gap with high quality, paint-able caulk. 8-18 by 0.323 inch (8.2 mm) head self-drilling, corrosion resistant ribbed buglehead screws. Product: 4/4 Boards, 5-1/2 inch (140 mm) width. Type: Hardie Architectural Multi-Groove Panel 4 by 12 feet (1219 by 3658 mm). Market:Default | 3). Las esquinas tambin pueden ser prefabricadas (fig. Slo las lengetas planas y de esquina pueden ser utilizadas con tablas HardieTrim para crear una sujecin oculta. 4). Artisan HZ10 lap siding requirement for Materials: Fiber-cement Siding - complies with ASTM E 84 Flame Spread Index = 0, Smoke Developed Index = 5. Type: Hardie Architectural Multi-Groove Panel 4 by 10 feet (1219 by 3048 mm). James Hardie does manufacture HardieWrap Weather Barrier, a non-woven non-perforated housewrap, which complies with building code requirements. 11 gauge 1-1/2 inches (38 mm) corrosion resistant roofing nails. or equivalent fasteners or screws may be used to attach HardieT. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions. Equilibrium Conditioned, psi: Greater than 1450 psi (10 MPa); Pass. Type: Select Cedarmill 6-1/4 inches (159 mm) with 5 inches (127 mm) exposure. If framing preparation is the responsibility of another installer, notify Architect of unsatisfactory preparation before proceeding. Adjacent finished grade must slope away from the building in accordance with local building codes - typically a minimum of 6 in. hardie trim james batten 8-18 by 0.375 inch (9.5 mm) head self-drilling, corrosion resistant S-12 ribbed buglehead screws. 4). Florida State Product Approval -FL13192, FL13223, and FL13265. power miter saws Always use a vacuum equipped with a HEPA filter to help minimize the amount of *Prices are pre-tax. Verification Samples: For each finish product specified, two samples, minimum size 4 by 6 inches (100 by 150 mm), representing actual product, color, and patterns. as manufactured by James Hardie Building Products, Inc. Net Free Ventilation: 12.6 sq inches of net free ventilation per linear foot (26670 sq mm per linear meter). Use weather cuts sloped away from the wall to join (fig. Wood Framing: 8d box ring common corrosion resistant nails. Minimum standard panel design size is 12 x 16 inches (). HardieTrim Boards: Fiber cement trim for corners and windows. Install over braced wood. Repair any punctures or tears in the water-resistive barrier prior to the installation of the siding. Tested in Accordance with ASTM E136: Classified as non-combustible. Shim frieze board as required to align with corner trim. If uncertain about exposure or protection in a specific situation, always consult a qualified industrial hygienist to determine actual exposure levels. ASTM E84: Surface Burning Characteristics. ASTM D3359 - Standard Test Method for Measuring Adhesion by Tape Test, Tool and Tape. 78-89, Products Installation Guide_HardieSoffit pg. Se recomienda la sujecin con una herramienta neumtica. Product Data: Manufacturer's data sheets on each product to be used, including: Preparation instructions and recommendations. Wet Conditioned, psi: Greater than 1015 psi (7 MPa); Pass. 24862. Type: HardieShingle Straight-Edge Notched Panel 48 inches (1219 mm) wide by 16 inches (406mm) high with 7 inches (178 mm) exposure. The bottom edge of the first two courses overlaps the starter strip. Do not nail within 2 inches (51 mm) of the end of planks. Product: 5/4 NT3 Boards, 5-1/2 inch (140 mm) width. Enter your zip code at www.hardiezone.com to find out what zone applies to your location. Product: 5/4 NT3 Boards, 11-1/4 inch (286 mm) width. 2). Fiber-cement trim - complies with ASTM E 136 as a noncombustible material. Apply starter course of 10 inches (254 mm) shingles or 9-1/2 inches (241 mm) lap siding overlapping the starter strip. Low Profile 45 degrees Inside Corner Trim: Aluminum extrusion to be used for bay windows. Protect edges and corners from chipping.

Type: Cedarmill Vertical siding panel 4 feet by 8 feet (1219 mm by 2438 mm). Metal Framing: 1.5 inch (38 mm) [AGS-100] .100 inches by 25 inches (2540 mm by 635 mm) ETandF Pin or equivalent pneumatic fastener. City of Los Angeles, Research Report No. Density: Less than 83 pounds per sq ft (4 kPa). Type: Hardie Architectural Panels - Fine Sand 4 by 12 feet (1219 by 3658 mm). Type: Beaded Smooth 8-1/4 inches (210 mm) with 7 inches (178 mm) exposure. Figure 28 BAND BOARD A ashing is required over the trim and Flat Tabs. Install kickout flashing at roof-wall junctions per manufacturer's instructions. Physical Observations Mass: No structural alteration; Pass. INSTALLATION - HARDIE ARCHITECTURAL PANELS. James Hardie Building Products provides installation /wind load information for buildings with a maximum mean roof height of 85 feet. Type: Select Cedarmill 5-1/4 inches (133 mm) with 4 inches (102 mm) exposure. For larger projects where the span of the wall is significant in length, the designer and/or architect should take into consideration the coefficient of thermal expansion and moisture movement of the product in their design. CONCEALED FASTENING TABS For Corners, Band Boards, Windows, and Door Applications: HardieTrim boards can be installed with Flat Tabs (JH sku no. Una las tablas de moldura y las lengetas planas alrededor de la apertura, tal y como se muestra en las figuras 26 y 27. Type: Select Cedarmill 9-1/4 inches (235 mm) with 8 inches (203 mm) exposure. Product Warranty: Limited, non-pro-rated product warranty. Acceptable Manufacturer: James Hardie Building Products, Inc., which is located at: 231 S. La Salle St. Suite 2000; Chicago, IL 60604; Toll Free Tel: 877-236-7526; Email: Requests for approval of equal substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements. Miami Dade County, -Notice of Acceptance -20-070.06. 11 gauge 1-3/4 inches (44 mm) corrosion resistant roofing nails. Store siding on edge or lay flat on a smooth level surface. Note: OSI Quad as well as some other caulking manufacturers do not allow tooling. Finish factory primed siding with a minimum of one coat of high quality 100 percent acrylic or latex or oil based exterior grade paint within 180 days of installation. Install metal Z flashing and provide a 1/4 inch (6 mm) gap at horizontal panel joints. Use a 2" finish nail to fasten trim together. Minimum 1-1/2 inches (38 mm) face and straight, true, of uniform dimensions and properly aligned. INSTALLATION - HARDIEPANEL HZ10 VERTICAL SIDING. siding Overlay siding with single board of outside corner board then align second corner board to outside edge of first corner board. Wood Framing: 0.093 inch (2.4 mm) shank by 0.222 inch (5.6 mm) head by 2 inches (51 mm) corrosion resistant siding nails. Install HardieTrim Fascia boards to rafter tails or to sub fascia. Wind Resistance: Where a specified level of wind resistance is required, Hardie Shingle siding is installed to substrate and secured with a minimum two fasteners described in Table No. Type: Stucco Vertical siding panel 4 feet by 10 feet (1219 mm by 3048 mm). Provide quantities as recommended by manufacturer. Product: 5/4 Boards, 7-1/4 inch (184 mm) width. For additional information on HardieWrap W, - NEVER use a circular saw blade that does not carry the HardieBlade, - NEVER dry sweep Use wet suppression or HEPA. Maintain a minimum 1 inch (25 mm) gap between end caps and siding and trim. Type: Hardie Architectural Panels - Fine Sand 4 by 10 feet (1219 by 3048 mm).

Each side of the pre-built corner must be secured to the wall (fig. 3).

Topcoat: Refer to Section 09 90 00 - Painting and Coating and Exterior Finish Schedule. Do not fasten HardieTrim boards to HardieTrim boards. Low-Profile Inside Corner Trim: Aluminum extrusion to be used for inside corners. 2022All rights reserved Shim frieze board as required to align with corner trim.. Fasten through overlapping boards. Type: Stucco Vertical siding panel 4 feet by 8 feet (1219 mm by 2438 mm). Horizontal Angled T Flashing Trim: Aluminum extrusion to be used along horizontal control joints. Wood Framing: 6d common corrosion resistant nails. Type: Sierra 8 inches (203 mm) Vertical siding panel 4 feet by 8 feet (1219 mm by 2438 mm). Wood Framing: 16 gauge 1-1/2 inches (38 mm) stainless finish nails. x 3.5 in. Product: 4/4 NT3 Boards, 5-1/2 inch (140 mm) width. If 5 Proper handling of James Hardie products Carrying James Hardie siding products with ColorPlus Technology flat may cause excessive bending, which can damage the finish. The James Hardie family of siding and trim products, including James Hardie products with ColorPlus Technology, should be stored in their original packaging in a garage, shed, or in some other covered area protected from weather whenever possible. Follow paint manufacturer's written product recommendation and written application instructions. The HardieBlade saw blade is specifically designed to cut fiber cement products while minimizing the amount of respirable silica dust. touch-up while the laminate sheet is in place. Loss Percentage: Less than or equal to 3.0 percent; Pass.. Freeze/Thaw, percent strength retention: Greater than or equal to 80 percent; Pass. Factory Finish: Refer to Exterior Finish Schedule. Minimum 1-1/2 inches (38 mm) face and straight, true, of uniform dimensions and properly aligned.

Install materials in strict accordance with manufacturer's installation instructions. WARNING: AVOID BREATHING SILICA DUST James Hardie products contain respirable crystalline silica, which is known to the State of California to cause cancer and is considered by IARC and NIOSH to be a cause of cancer from some occupational sources. Match touch up color to siding color through use of manufacturer's branded touch-up kits. Sweeping dry material may send !

• Tamalitoz Candy Near Milton, On
• 6 Gram Mushroom Chocolate Bar
• Outdoor Classroom Supplies
• Kitchenaid Meat Grinder Screw
• 8mm White Gold Wedding Band
• Full Circle Detail Brush
• Chocolove Salted Almond Butter
• Uhmwpe Chemical Compatibility
• Chauvet Slim Strip Uv-18 Irc
• Custom Women's Pajamas
• Coil Binding Machine Near Me
• Best Bubble Bath For Sensitive Skin Uk
• Vero Moda Puff Sleeve Sweater
• Eucerin Sensitive Skin Toner
• Slip-on Construction Shoes
• Homewood Suites By Hilton Lansdale
• Clean Blossom Perfume
• How To Connect Sentry Bluetooth Earbuds
• Hotel Palladium Palma

Sitemap 19

Submitted in: madewell petite pants |